Коды ошибок рефрижераторных установок Mitsubishi TDJS Series.

Mitsubishi Transport Refrigeration Unit TDJS Series.

List of alarm codes.

Alarm Code	Trouble	Countermeasure	Alarm Lamp	Unit Condition
E003	Magnet clutch fuse break	Magnet clutch fuse F2* is blown. Inspect and replace if necessary the fuse F2* in the control box	On	Unit stops
E006	Load drive circuit fuse break	Load power supply relay fuse F7* is blown. Inspect and replace if necessary the fuse F7* in the control box	On	Unit stops
E010	HP abnormally high	High-pressure switch has tripped (1) Check if the condenser fan is running. If it is not, check the fuse F3* – or for disconnected wires in the control box (2) Inspect if the condenser coil is fouled with dirt or mud. If it is, wash it with a soft brush and water	On	Unit stops
E013	Td abnormally high	Discharge gas temperature is abnormal. Check for bubbles in the sight glass. If bubbles are observed, ask a service shop for inspection	On	Unit stops
E014	Refrigerant shortage	Refrigerant quantity is insufficient. Ask a service shop for inspection	On	Unit stops
E016	LPT failure	Broken wire or short-circuit on the low-pressure sensor. Ask a service shop for inspection	Blinking	Unit operation continues
E017	HPT failure	Broken wire or short-circuit on the high-pressure sensor. Ask a service shop for inspection	Blinking	Unit operation continues
E040	DCS2 shortcircuit (Abnormal stop output)	Short-circuit on the abnormal stop output circuit. Ask a service shop for inspection. Ask a service shop for inspection	Blinking	Unit operation continues
E041	DCS1 shortcircuit (Operation output)	Short-circuit on the operation output circuit. Ask a service shop for inspection. Ask a service shop for inspection	Blinking	Unit operation continues
E042	DCS3 shortcircuit (Out of range inside container)	Short-circuit on the out of range inside container temperature output circuit. Ask a service shop for inspection	Blinking	Unit operation continues
E050	TH sensor failure	*Lo (1).** Short-circuit or poor connector connection on the inside container temperature sensor. Ask a service shop for inspection	On, or blinking if setting temperature is lower than -10 ˚C	Unit stops (Or continuous cooling operation if setting temperature is lower than -10 ˚C.)
E050	TH sensor failure	*Hi (1).** Short-circuit on the inside container temperature sensor. Ask a service shop for inspection	On, or blinking if setting temperature is lower than -10 ˚C
E057	EVT sensor failure	Broken wire or short-circuit on the evaporator exit temperature sensor. Ask a dealer for inspection	Blinking	Unit operation continues
E063	Td sensor failure	Broken wire or short-circuit on the discharge gas temperature sensor at the engine side Ask a dealer for inspection	Blinking	Unit operation continues
E067	Td sensor failure (Motor side)	Broken wire or short-circuit on the discharge gas temperature sensor at the motor side Ask a service shop for inspection	Blinking	Unit operation continues
E099	Controller communication failure	Cabin controller cannot communicate properly. Ask a service shop for inspection	On	Unit stops
E101	Evaporator fan motor fuse break	Evaporator fan motor fuse F1* is blown. Inspect and replace if necessary the fuse F1* in the control box. In case of 2-compartment model, if the evaporator fan motor fuse at second compartment is abnormal, inspect and replace if necessary the fuse F4* in the control box	Blinking	Unit operation continues
E102	Condenser fan motor fuse break	Condenser fan motor fuse F3* is blown. Inspect and replace if necessary the fuse F3* in the control box	Blinking	Unit operation continues
E104	Drain hose heater fuse break	Drain hose heater fuse F6* is blown. Inspect and replace if necessary the fuse F6* in the control box	Blinking	Unit operation continues
E160	Economizer SV shortcircuit (TDJS70*ZE only)	Short-circuit on the economizer solenoid valve SV6 circuit. Ask a service shop for inspection	Blinking	Unit operation continues
E161	Economizer SV shortcircuit	Short-circuit on the fluid line solenoid valve SV5F circuit. Ask a service shop for inspection	On	Unit stops
E163	Hot gas line SV shortcircuit	Short-circuit on the hot gas solenoid valve SV1 circuit. Ask a service shop for inspection	Blinking	Unit operation continues
E167	Condenser outlet SV shortcircuit	Short-circuit on the condenser exit solenoid valve SV3 circuit. Ask a service shop for inspection	On	Unit stops
E168	Liquid bypass SV shortcircuit	Short-circuit on the fluid bypass solenoid valve SV2 circuit. Ask a service shop for inspection	Blinking	Unit operation continues

* – Indicates the smallest digit of fuse No.

*1 – Lo or Hi is indicated on the temperature display.

– In case of 2-compartment model, which of the parts that controls compartment is faulty is indicated with the A or B compartment operation indicator.